濾波器的選擇:根據干擾源的特性、頻率范圍、電壓和阻抗等參數及負載特性的要求,適當選擇濾波器,一般考慮:
其一,要求電磁干擾濾波器在相應工作頻段范圍內,能滿足負載要求的衰減特性,若一種濾波器衰減量不能滿足要求時,則可采用多級聯,可以獲得比單級更高的衰減,不同的濾波器級聯,可以獲得在寬頻帶內良好衰減特性;
其二,要滿足負載電路工作頻率和需抑制頻率的要求,如果要抑制的頻率和有用信號頻率非常接近時,則需要頻率特性非常陡峭的濾波器,才能滿足把抑制的干擾頻率濾掉,只允許通過有用頻率信號的要求;
其三,在所要求的頻率上,濾波器的阻抗必須與它連接干擾源阻抗和負載阻抗相失配,如果負載是高阻抗,則濾波器的輸出阻抗應為低阻;如果電源或干擾源阻抗是低阻抗,則濾波器的輸入阻抗應為高阻;如果電源阻抗或干擾源阻抗是未知的或者是在一個很大的范圍內變化,很難得到穩定的濾波特性,為了獲得濾波器具有良好的比較穩定的濾波特性,可以在濾波器輸入和輸出端,同時并接一個固定電阻。其四,濾波器必須具有一定耐壓能力,要根據電源和干擾源的額定電壓來選擇濾波器,使它具有足夠高的額定電壓,以保證在所有預期工作的條件下都能可靠地工作,能夠經受輸入瞬時高壓的沖擊。其五,濾波器允許通過應與電路中連續運行的額定電流一致。額定電流高了,會(huì )加大濾波器的體積和重量;額定電流低了,又會(huì )降低濾波器的可靠性,其六,濾波器應具有足夠的機械強度,結構簡單、重量輕、體積小、安裝方便、安全可靠。
濾波器的使用:為了提高電源的品質、電路的線性、減少各種雜波和非線性失真干擾和諧波干擾等均使用濾波器。對相關系統來講,使用濾波器的場所有:
其一,除總配電系統和分配電系統上設置電源濾波器外,進入設備的電源均要安裝濾波器,最好使用線至線濾波器,而不使用線至地濾波器;
其二,對脈沖干擾和瞬變干擾敏感的設備,使用隔離變壓器供電時,應在負端加裝濾波器;
其三,對含電爆裝置的相關系統供電時,應加濾波器。必要時,電爆裝置的引線也要加裝濾波器;
其四,各分系統或設備之間的接口處,應有濾波器抑制干擾,確保兼容;
其五,設備和分系統的控制信號,其輸入和輸出端均應加濾波器或旁路電容器。